Features
  • Measurement functions:
    20MPS Oscilloscope (WFT)
    Frequency Counter (FCT)
    Function Generator (FGT)
    Digital Input/Output (DIO), all in one unit
  • Test controller function (FxAutoTest.exe tool)
  • Using these 4 measurement functions, test program can be edited by
    an application FxAutoTest.exe, according to the DUT's test sequence
  • Test programs may be saved in the module
  • Test common is isolated with power supply and control GND

WFT - Module Panel

Specification

Click here to view product specification in PDF (Acrobat Reader required)

WFT700
Vertical (Y-axis)

Volt/Div range

10mV/div ~ 10V/div

Frequency bandwidth

DC - 10MHz ( With AC combination 10Hz ~)

Coupling

AC , DC , GND

Input Impedance

1MΩ±2% // 20pF ±2pF

Max Input Voltage

±40V ( DC + AC peak )

DC Gain Precision Value read × ±0.5% ±0.05div × Voltage/div
AC Gain Precision

Value read × ±1.0% ±0.10div
× Voltage/div( DC ~ 100KHz )





 

 


Trigger

Synchronous

Edge

Signal Source

CH1, CH2

Coupling

DC , AC (CH1, CH2)

Polarity

+ / -

Level

±4div

 

 

 

Time (x-axis)

Sweep Time

500ns/div - 1s/div

Acquisition mode

Normal / Single

Resolution

12Bit

Max Sample Rate

20MPS (CH1,CH2 simultaneous); 40MPS (CH1 only)

Wave Memory 128KWord/CH (256K at 40MPS)

Sample Mode

Normal sampling

 

 

 

 

Automatic measurement

4 measurement items can be executed at the same time.
Measurement display: Rise time, fall time, time-interval of plus-pulse width, minus-pulse width, duty, signal frequency, effective period-voltage reading from signal, effective period-voltage reading, average voltage reading, maximum value on the plus-side, and maximum value on the minus-side, voltage amplitude, high voltage, low voltage, peak-to-peak.


FCT700

Frequency range

0.1Hz - 20MHz

Average Period

0.01s ~ 9.99999s

Pulse Width

0.01s ~ 9.99999s

Time Interval

0.01s ~ 9.99999s

Duty

0.1 ~ 99.9%

Low Pass Filter Function

Can mask 4s from either edge of the
measured signal pulse

 

 

 

 

FGT700
Wave Output

Output Wave

Sine wave ( 0.5Hz - 2MHz ), square wave, triangular wave, ramp wave, arbitrary wave (0.5 ~ 200kHz )

Output mode

Single, repeat

Wave Amplitude

±10 V (Amplitude + DC Offset )

Output Current

±10 mA

Output Impedance

50 Ω

 

 




Arbitary Output

Wave data

Max 2000 ( 200 to 2000)

Vertical resolution

10 bit

DDS Clock

20 to 19999999 (MAX 20MHz)





DC Output

Output Voltage

±10 V (10 Bit resolution)

Output Current

±10 mA

Output Impedance

50 Ω





DIO700

Byte direction

In/Output/Keep

Input/output line

TTL level with 33Ω resistor at serial

Input mode

Capable of comparing input with expected value

Input Current

0.1 mA

Output Current

10 mA

 

 



FX auto test builder

Home


Contents copyright 1998-2007 Qualectron Systems Corporation. For comments, inquiries or suggestions about this Web site, send e-mail to info@qualectron.com

ATS Builder

 

Home

Multifunction Tester
FX-700

 


Information Request